油水分离器是什么？工作原理有什么？

发布人：http://www.sftfgd.com   发布时间：2018-05-22 15:28:33

    无动力油水分离器是什么？
    What is an unpowered oil-water separator?
    无动力油水分离器是由预过滤器、聚结分离器、吸附过滤器、泵体、控制箱、车体组成的一种水中除油的过滤设备。无动力油水分离器可处理含油量在5000mg/L的所有的工业上用的轻质油类，简单的说就是在水多油少的情况下，要使用无动力油水分离器来进行油和水的分离。
    An unpowered oil-water separator is a filter equipment consisting of a pre filter, a coalescer, an adsorption filter, a pump body, a control box, and a car body. The unpowered oil-water separator can handle all the light oil used in the industry of 5000mg/L, which is simply to use the unpowered oil-water separator to separate the oil and water in the case of less water.
    无动力油水分离器工作过程？
    The working process of the unpowered oil-water separator?
    1、启动泵源开关，依次打开预过滤器、聚结过滤器上的排气阀，待排气阀有水溢出时，表明该腔体内已充满水，此时关闭该排气阀，待各腔体均充满水时，打开出水球阀。也可以通过电磁阀手动排气，排气过程一般只需在在设备刚开始工作时进行，设备正常运行后不需排气。根据出水水质情况，可以通过出水阀适当调节进水流量的大小，出水水质差可减小流量，反之可增大流量。

    start the pump source switch, turn on the exhaust valve on the pre filter and the coalescence filter in turn. When the exhaust valve has water overflow, it shows that the cavity is filled with water. At this time, the exhaust valve is closed and the water ball valve is opened when all the cavities are filled with water. It can also be manually exhausting through the solenoid valve. The exhaust process is usually carried out at the beginning of the operation of the equipment, and no exhaust is required after normal operation of the equipment. According to the effluent quality, the influent flow can be properly adjusted through the outlet valve. The poor water quality can reduce the flow rate, otherwise the flow rate can be increased.
    2、清水从出水口排出，集油室开始集油，油水界面开始下降。当油浸没住传感器的电极棒时，传感器输出信号，电磁阀处于开通状态，排油电磁阀开始排油，此时相应的电磁阀指示灯亮，当排油控制箱设定的延时时间到时，排油电磁阀关闭，排油指示灯熄灭，排油结束。排油后，油水界面开始上升，电极棒处于水中时，传感器停止输出信号，从观察窗上可以观察油位高低。
    The water is discharged from the outlet, and the oil gathering room begins to collect oil, and the oil-water interface begins to decline. When the oil impregnated with the electrode rod of the sensor, the sensor output signal, the solenoid valve is in the open state, the oil discharge electromagnetic valve starts to drain. At this time the corresponding electromagnetic valve indicator light is bright. When the delay time of the oil control box is set, the oil discharge electromagnetic valve is closed, the oil discharge indicator is extinguished and the oil discharge is finished. After the oil discharge, the oil water interface starts to rise. When the electrode bar is in the water, the sensor stops the output signal, and the oil level can be observed from the observation window.
    3、每次停机前应将清水注满水油分离器各腔体并关闭进、出水球阀。若长时间停机不用，应在停机前以清水运行20分钟，直存油全部从油水分离器内腔排出。
    finally, every time before stopping, fill the water and oil separator with water and close the inlet and outlet ball valves. If there is no need to stop for a long time, clear the water for 20 minutes before stopping, until the oil is discharged from the inner cavity of the oil-water separator.