铁皮通风管道安装要注意哪些质量控制？

发布人：http://www.sftfgd.com   发布时间：2021-11-15 11:05:56

来讲，就白铁皮通风管道在进行安装的时候，先要注意的其实也就是通风管道上的组装，在风管比较短的时候，在很大的程度上其实也就是能一次在地面进行组装而成，紧接着，就风管比较长的时候，在很大的程度上其实也就是能直接的就视安装场地的情况，直接的就在地面进行分段组装。

First of all, when installing the white iron sheet ventilation duct, the first thing to pay attention to is the assembly on the ventilation duct. When the air duct is relatively short, it can be assembled on the ground to a great extent. Then, when the air duct is relatively long, it can directly depend on the situation of the installation site to a great extent, It is directly assembled in sections on the ground.

就济南白铁皮通风管道在进行组装的时候，应该是要尽量调整一下其风道的度与水平度，就其在很大的程度上其实也就是能直接的就避免了风管扭曲或者是上下起波，左右摆动，且就每段风道上其实也也就是要注意不可以超过10m。在进行组装的时候，垫片也应该要注意垫平，对于其法兰螺栓也应该是要均匀的进行拧紧，就螺母帽均会朝向同一方向。

When assembling the Jinan white iron sheet ventilation duct, it should try to adjust the centrality and levelness of the air duct as much as possible. To a great extent, it can directly avoid the air duct distortion or wave up and down, swing left and right, and in fact, it should not exceed 10m in each section of the air duct. During assembly, the gasket should also be leveled. The flange bolts should also be tightened evenly, and the nut caps will face the same direction.

再者，关于白铁皮通风管道上的就位，就风管在进行就位之前，在很大的程度上其实也就是应该要注意直接的就检查一下其全部支架上的水乎度与标高，紧接着，也就是要注意应该是要直接的就检查一下其支架的牢固程度，对于其风管就位其实也就是能采用直接与吊具这两种方法。

In addition, for the positioning of the white iron sheet ventilation duct, before the air duct is positioned, it should be paid attention to directly check the water level and elevation of all its supports. Then, it should be paid attention to directly check the firmness of its supports, In fact, the two methods of direct and spreader can be adopted for the positioning of the air duct.

紧接着，对于济南白铁皮通风管道上的风管断面上比较小，又其位置上比较低的话，在很大的程度上其实也就是可以直接的就可以采用人工就位方法，只需要直接的就搭设简易脚手架也就可以了。就白铁皮通风管道上的风管断面比较大并且就其管段上比较长的时候，就其在很大的程度上其实也就是能直接的就采用滑轮、倒链或者是大绳等方法进行吊装。为了方便通风管道上的风道进行就位，一般情况下也就是要注意应该是直接把风道吊在了脚手架上面。

Then, if the section of the air duct on the Jinan white iron sheet ventilation duct is relatively small and its position is relatively low, to a large extent, the manual positioning method can be directly adopted, and it only needs to directly set up a simple scaffold. When the section of the air duct on the white iron sheet ventilation duct is relatively large and the pipe section is relatively long, it can be hoisted directly by pulley, chain block or large rope to a great extent. In order to facilitate the positioning of the air duct on the ventilation duct, it should be noted that the air duct should be directly hung on the scaffold.