工业空调的风管加工有哪些规范和注意事项?

发布人：http://www.sftfgd.com   发布时间：2022-05-06 16:33:16

在车间通风降温工程中，空调通风管道的加工安装是一个非常重要的环节。通风管道的加工和安装方法有一些具体的，才能与空调连接，发挥其作用，完成其使用效果。

1： Specifications. The specifications mentioned here are the basic specifications of the ventilation duct, as well as the size and size of the ventilation duct we need. It is worth noting that when we determine the specifications, we need to be associated with the use of air conditioning. Only in this way can we ensure that after setting the specifications of the ventilation duct, it can be connected with the air conditioner, play its role and complete its use effect.

二：类型。通风管的种类很多。不同类型的空调与管道配合使用，效果不同，尤其是通风管道的隔热。因此，如果我们要加工通风管道以更好地与空调配合使用，我们还需要在加工前考虑其类型，这是确保它们高工作并发挥有利作用的良好条件。

2： Type. There are many kinds of ventilation pipes. Different types of air conditioners have different effects when used together with pipes, especially the heat insulation of ventilation pipes. Therefore, if we want to process ventilation ducts to better cooperate with air conditioners, we also need to consider their types before processing, which is a good condition to ensure their high work and play a favorable role.

总之，在加工通风管之前，一定要结合空调的基本情况，注意通风管的规格和类型。不同的空调需要不同的通风管、不同的规格、不同的类型。因此，当涉及到通风管道时，需要考虑上述问题。

In short, before processing the ventilation pipe, we must pay attention to the specification and type of the ventilation pipe in combination with the basic situation of the air conditioner. Different air conditioners need different ventilation pipes, different specifications and different types. Therefore, when it comes to ventilation ducts, the above problems need to be considered.

通风管道加工规范：

Ventilation duct processing specification:

1、风管加工时，为保证风管生产后的强度，切割时应预留20mm铝箔作为保护边;

1. During air duct processing, 20mm aluminum foil shall be reserved as protective edge during cutting to ensure the strength of air duct after production;

2、风管在拼接前需要预先组装好，检查接缝是否严密，尺寸是否符合要求。根据季节温度、湿度和粘合剂特性确定粘合时间。加入后，用正方形检查。钢带。垂直度和对角线偏差的调整需要符合规定。

2. The air duct needs to be pre assembled before splicing to check whether the joint is tight and whether the size meets the requirements. The bonding time is determined according to the seasonal temperature, humidity and adhesive characteristics. After adding, check with a square. Steel belt. The adjustment of perpendicularity and diagonal deviation shall meet the requirements.

3、通风管道加工时，请做好现场预制板、管道成品的保护工作。

3. During the processing of ventilation pipes, please protect the prefabricated plates and finished pipes on site.

4、连接安装后，应检查接头接头，接头后应平整、弯曲。错位局部裂纹、大于2mm的缝隙等缺陷。

4. After connection and installation, check the joint, which shall be flat and bent. Dislocation, local crack, gap larger than 2mm and other defects.

5、风管支架与吊架的距离符合标准。

5. The distance between air duct support and hanger meets the standard.

以上就是为大家介绍的有关济南铁皮风管加工http://www.sftfgd.com的详细的介绍,希望对您有所帮助.如果您有什么疑问的话,欢迎联系我们.我们将以的态度,为您提供服务

The above is about the processing of Jinan iron sheet air duct http://www.sftfgd.com I hope it will be helpful to you If you have any questions, please contact us We will provide you with professional service