通风管道加工的注意事项有哪些？

发布人：http://www.sftfgd.com   发布时间：2022-08-19 17:12:46

现在通风管道大家都现已了解了吧，在建筑业快速展开的现在，高层建筑越来越多，为了保护在内工作人员的身体健康，通风管道的运用也多了起来，在给通风管道加工时，有许多事项要注意，下面主要是一些常见的问题：

Now we all know about the ventilation ducts. With the rapid development of the construction industry, there are more and more high-rise buildings. In order to protect the health of the staff inside, the use of ventilation ducts is also increasing. There are many matters to pay attention to when processing the ventilation ducts. The following are some common problems:

1、通风管道加工的过程中应该尽量防止呈现纵向接缝，可是必定不能呈现横向接缝。并且通风管道的咬口缝和四角的缝隙处，需求依照规划洁净等级要求，然后还要选用密封胶将其堵严。其他通风管道板材的衔接缝的密封面应该设在通风管道壁的正压侧。

1. Longitudinal joints shall be prevented as much as possible during the processing of ventilation pipes, but transverse joints shall not be allowed. In addition, the undercut joints and the four corners of the ventilation pipe shall be sealed with sealant according to the requirements of the planned cleanliness level. The sealing surface of the joint of other ventilation duct plates shall be set at the positive pressure side of the ventilation duct wall.

   
   

2、加工的时分，不能在通风管道内部设置加固框或许加固筋，由于这样关于通风管道的质量会造成必定的影响。

2. During processing, it is not allowed to set reinforcement frame or reinforcement bar inside the ventilation duct, because the quality of the ventilation duct will be affected.

3、通风管道加工不能选用S型插条和C型直角插条的衔接办法，其他关于一些特其他通风管道来说，还不能选用按扣式的咬口。

3. The connection method of S-type and C-type right angle inserts cannot be selected for the processing of ventilation pipes. For other special ventilation pipes, the snap type bite cannot be selected.

4、通风管道制作结束之后，还要用清洗液进行清洗，只要到达清洗规范之后，才可以及时封口。

4. After the ventilation pipe is manufactured, it should be cleaned with cleaning liquid. As long as the cleaning specification is reached, it can be sealed in time.

5、假设是五颜六色涂层钢板通风管道的话，应该坚持内壁是润滑的，并且通风管道加工的过程中，还不能将涂层损坏，若是呈现损坏的部位，需求用环氧树脂涂刷在表面即可。其他通风管道加工的过程中，还要做好防腐蚀措施，不能使用抽芯铆钉，并且在通风管道零件安装的时分，这些零件都要通过镀锌处理才行。

5. If it is a colorful coated steel plate ventilation pipe, the inner wall should be kept lubricated, and the coating should not be damaged during the processing of the ventilation pipe. If the damaged part appears, it needs to be painted on the surface with epoxy resin. During the processing of other ventilation pipes, anti-corrosion measures shall be taken, and blind rivets shall not be used. Besides, during the installation of ventilation pipe parts, these parts shall be galvanized.

如果做到以上问题不出错的话，在给通风管道加工时应该没有多大问题!

If the above problems are not wrong, there should be no big problem when processing the ventilation duct!

以上就是为大家介绍的有关济南铁皮风管加工的详细的介绍,希望对您有所帮助.如果您有什么疑问的话,欢迎联系我们.我们将以的态度,为您提供服务http://www.sftfgd.com

The above is the detailed introduction about the processing of Jinan iron sheet air duct. I hope it will help you. If you have any questions, please contact us. We will provide you with services with a professional attitude http://www.sftfgd.com