当前位置:首页-新闻中心新闻中心

不锈钢通风管道安装注意事项

发布人:http://www.sftfgd.com   发布时间:2022-11-09 19:35:00

在由板材变成螺旋风管成品的过程中,生产厂家、安装公司、业主都是各司其责,相互之间的合作紧密性不高,因而在实际操作过程中存在的问题很多都不能得到科学地解决,使得优良的板材在被制作成螺旋风管后未必能充分发挥其优良的性能,从而严重地制约了空调系统和目标的实现。

In the process of turning the plate into a finished spiral air duct, the manufacturers, installation companies and owners are all responsible for their own work, and the cooperation between them is not very close. Therefore, many problems in the actual operation process can not be solved scientifically, which makes it impossible for excellent plates to give full play to their excellent performance after being made into spiral cyclone tubes, which seriously restricts the realization of energy conservation and environmental protection goals of the air-conditioning system.

不锈钢板的强度要比普通钢板高,用不锈钢板咬口前,要作成形试验,避免使设备*负荷作业,形成过度磨损或机械事端。由于铝板塑性差,咬口成形时容易开裂,施工前也要作成形试验,同时,因铝板缺乏弹性,铝板风管不能进行按扣式咬口。

The strength of stainless steel plate shall be higher than that of ordinary steel plate. Before seaming with stainless steel plate, forming test shall be carried out to avoid excessive wear or mechanical accidents caused by equipment * load operation. Due to the poor plasticity of the aluminum plate, it is easy to crack during the forming of the seaming. The forming test should also be carried out before construction. At the same time, because the aluminum plate is lack of elasticity, the aluminum plate air duct cannot be seamed with a snap fit.

QQ截图20170428145504.png

安装注意事项

Installation precautions

1、铆钉脱落:按工艺操作、铆后检查、使用合适的螺钉。

1. Rivet falling off: operate according to the process, check after riveting, and use appropriate screws.

2、风管法兰连接不方:用方尺找正使法兰与直管棱垂直,管口四边翻边适量。

2. Improper connection of air duct flange: use a square ruler to align the flange to make it perpendicular to the straight pipe edge, and the four sides of the pipe orifice are properly flanged.

3、法兰翻边四角漏风:管片压口前到倒角、咬口重叠处翻边时铲平、四角不应出现豁口。

3. Air leakage at the four corners of flange flanging: the flanging from the front of the segment pressure opening to the chamfer and overlap of the undercut shall be leveled, and the four corners shall be free of cracks.

以上就是为大家介绍的有关济南通风管道的详细的介绍,希望对您有所帮助.如果您有什么疑问的话,欢迎联系我们.我们将以的态度,为您提供服务http://www.sftfgd.com

The above is a detailed introduction to the ventilation pipes in Jinan. I hope it will be helpful to you. If you have any questions, please contact us. We will provide services for you with our attitude http://www.sftfgd.com


上一篇:通风管道在运输过程应做好哪些防护措施
下一篇:通风管道在运输过程应做好哪些防护措施

网站首页 关于我们 产品展示 新闻中心 工程案例 在线留言 联系我们