螺旋风管其长度等方面是要好于矩形风管

发布人：http://www.sftfgd.com   发布时间：2022-11-17 19:52:03

螺旋风管其长度等方面是要好于矩形风管：这是由于普通的螺旋风管，其正常长度是为3米到6米，而矩形风管其是为1米到1.5米，除此之外，螺旋风管的长度，还能够依照具体需求来定做，从其它方面来看，螺旋风管中的连接点，是能够很大程度上根绝的，由于其风管之间的连接，只用管接件，而矩形风管则需求双法兰体系。

The length of spiral air duct is better than that of rectangular air duct: this is because the normal length of ordinary spiral air duct is 3 to 6 meters, while that of rectangular air duct is 1 to 1.5 meters. In addition, the length of spiral air duct can also be customized according to specific needs. From other aspects, the connection points in spiral air duct can be eliminated to a large extent. Because the connection between air ducts only uses pipe connectors, The rectangular air duct requires double flange system.

1、通风管道加工的过程中应该尽量避免出现纵向接缝，但是一定不能出现横向接缝。而且通风管道的咬口缝和四角的缝隙处，需要按照设计洁净等级要求，然后还要采用密封胶将其堵严。另外通风管道板材的连接缝的密封面应该设在通风管道壁的正压侧。

1. The longitudinal joint shall be avoided as far as possible during the processing of the ventilation pipe, but the transverse joint shall not be allowed. Moreover, the seaming seams and the four corners of the ventilation pipe shall be sealed with sealant according to the design cleanliness level requirements. In addition, the sealing surface of the joint of the ventilation duct plate should be set at the positive pressure side of the ventilation duct wall.

镀锌螺旋风管

Galvanized spiral air duct

2、加工的时候，不能在通风管道内部设置加固框或者加固筋，因为这样对于通风管道的质量会造成一定的影响。

2. During processing, reinforcing frames or reinforcements cannot be set inside the ventilation ducts, because this will have a certain impact on the quality of the ventilation ducts.

3、通风管道加工不能采用S型插条和C型直角插条的连接方式，另外对于一些特殊的通风管道来说，还不能采用按扣式的咬口。

3. The connection mode of S-shaped and C-shaped right angle inserts cannot be used for the processing of ventilation ducts. In addition, snap joint cannot be used for some special ventilation ducts.

4、通风管道制作完毕之后，还要用清洗液进行清洗，只有达到清洗标准之后，才可以及时封口。

4. After the fabrication of the ventilation pipe, it shall be cleaned with cleaning solution. Only when the cleaning standard is met, can it be sealed in time.

5、玻璃纤维复合板风管端口为切割面时，在装配法兰连接件前应将管端切口面用胶带或胶液进行封堵，才能防止玻璃纤维外露和飞散

5. When the end of the fiberglass composite board air duct is the cutting surface, the cut surface of the duct end should be sealed with tape or glue before assembling the flange connector to prevent the fiberglass from being exposed and flying

以上就是为大家介绍的有关济南风管加工厂的详细的介绍,希望对您有所帮助.如果您有什么疑问的话,欢迎联系我们.我们将以的态度,为您提供服务http://www.sftfgd.com

The above is a detailed introduction to Jinan Air Duct Processing Factory, and I hope it will be helpful to you. If you have any questions, please contact us. We will provide services for you with our attitude http://www.sftfgd.com