为了保证通风管道顺利使用要进行正确安装！

发布人：http://www.sftfgd.com   发布时间：2023-07-03 15:59:12

大家都知道我们常用的通风管道要求采用不燃材料，是为了防止高温引起火灾或火灾发生时火焰越过防火阀而造成更大的损失，那么为了保证通风管道顺利使用要如何对其正确安装加工呢？下面济南通风管道厂家为您分析：

Everyone knows that our commonly used ventilation ducts require the use of non combustible materials to prevent fires caused by high temperatures or greater losses caused by flames crossing the fire damper in the event of a fire. So, how to correctly install and process the ventilation ducts to ensure their smooth use? Below is an analysis by the ventilation pipeline manufacturer in Jinan:

1、通风管道在运输过程应有防止损伤风管的保护措施。

1. Ventilation ducts should have protective measures to prevent damage to the ducts during transportation.

2、榫接风管的连接在榫口处涂胶粘剂，是为增强接头处的强度。

2. The connection of the mortise and tenon air duct is coated with adhesive at the mortise to enhance the strength of the joint.

3、当风管采用地面预组装后架空安装时，限制预组装的长度是为了遮免风管因自重产生的弯曲而破坏构件接口。

3. When the air duct is installed overhead after ground pre assembly, limiting the length of pre assembly is to prevent the bending of the air duct due to its own weight from damaging the component interface.

4、玻璃纤维复合板风管端口为切割面时，在装配法兰连接件前应将管端切口面用胶带或胶液进行封堵，才能防止玻璃纤维外露和飞散。

4. When the end of the fiberglass composite board air duct is a cutting surface, the cutting surface of the pipe end should be sealed with tape or glue before assembling the flange connection to prevent the fiberglass from being exposed and flying.

5、非法兰连接的玻璃纤维复合板风管垂直安装的支撑件制作与安装的方法。

5. Method for manufacturing and installing support components for vertical installation of non flange connected glass fiber composite board air ducts.

6、竖井内通风管道垂直安装，由于空间少，又不便于以后检修，故风管一般采用外套角钢法兰连接以增加连接点的牢固程度和强度，并把法兰作成“井”形，吊筋直接吊在角钢法兰的吊耳上而不另设支撑件。

6. The ventilation ducts inside the vertical shaft are installed vertically. Due to the limited space and inconvenient maintenance in the future, the air ducts are generally connected with outer angle steel flanges to increase the firmness and strength of the connection points. The flanges are also made into a "well" shape, and the hanging bars are directly hung on the lifting lugs of the angle steel flanges without additional support components.

风管安装加工是将法兰的槽口套插在风管管板的端头，用胶粘剂粘接。如果其间没有过盈量，槽口和风管端面插入时会有间隙，使其无法粘为一体。更多相关事项就来我们网站http://www.sftfgd.com咨询！

The installation and processing of air ducts involves inserting the groove of the flange into the end of the air duct board and bonding it with adhesive. If there is no interference between them, there will be a gap between the slot and the end face of the air duct when inserted, making it impossible to stick together. For more related matters, come to our website http://www.sftfgd.com consulting service